Realization of a High-Speed, High-Power 300 GHz-Band Signal Generation System to Accelerate 6G Development

World's fastest 280 Gbps high-power signal generation achieved using a wideband amplifier

NTT Corporation
NTT Innovative Devices Corporation
Keysight Technologies, Inc.
June 16, 2025

In 6G, sub-terahertz waves (radio waves in the 100 GHz to 300 GHz frequency band), which offer access to wide bandwidths, are expected to enable ultra-high-speed wireless communication and high-precision radar sensing. For the research, development, and practical implementation of systems using sub-terahertz waves, system validation and evaluation using modulation signals2 are essential.

In the 300 GHz band—anticipated for use in ultra-high-speed wireless communications exceeding 100 Gbps— WR3.4 waveguide3 in the J-band (220 GHz to 325 GHz) are commonly used as input/output interfaces for measurement equipment. Therefore, in the development of wireless communications and radar systems using the J-band, it is crucial to have a signal generation system that supports the J-band and can generate high-power, high-speed modulated signals.

However, amplifying signals in the J-band is technically demanding, and as the signal speed and power increase, the adverse effects of signal distortion become more significant. These challenges have made it difficult for conventional signal generation systems to achieve both high output power and high modulation speed simultaneously.

To realize an evaluation signal generation system capable of producing high-speed, high-power modulated signals in the J-band, NTT, NTT Innovative Devices, and Keysight collaborated on the following research and development efforts.

NTT designed and developed a new amplifier integrated circuit (IC) equipped with a wideband impedance matching circuit and a low-loss combiner circuit (Figure 1(a)). This amplifier IC was designed using a high-speed InP-based compound semiconductor4, originally developed by NTT. Thanks to this circuit configuration, low-loss signal combining across the full J-band—previously a major technical challenge—was achieved, enabling high output power across the entire J-band frequency range.

Furthermore, by applying the distortion compensation technology developed by Keysight to the amplifier module jointly developed by NTT and NTT Innovative Devices, a signal generation system was constructed that successfully combines wide bandwidth with high linearity (Figure 2). As a result, high-speed, high-power signal generation was achieved.

NTT Innovative Devices manufactured the amplifier IC designed by NTT using the aforementioned InP-based compound semiconductor. The IC was mounted in a low-loss J-band waveguide package also designed by NTT, resulting in the development of an amplifier module that was provided for this experiment (Figure 1(b)). This amplifier module covers the entire J-band and achieves a maximum output power of +9.1 dBm.

Keysight contributed its proprietary system for measuring signal distortion characteristics (Vector Component Analyzer5) and its high-precision distortion compensation signal processing technology, known as Digital Pre-Distortion (DPD) (Figure 2). This technology measures the distortion generated in the system and pre-corrects the input signal to reduce distortion in the output. In this study, DPD was successfully applied in the 300 GHz band, achieving the world’s highest data rate to date in this frequency range.

Through these efforts, the team succeeded in generating a modulated signal at 280 Gbps (35 GBaud6 256-QAM7)—the highest reported data rate in the 300 GHz band (Figure 3). The output power reached 0 dBm, approximately 8 times higher than that of previous records (−9 dBm8), marking a major step forward in generating practical high-power signals (Figure 4).

(a)

(b)

Figure 1 (a) Microscope Image of Amplifier IC (b) External View of Amplifier Module

(a)

(b)

Figure 2 Measurement Setup of Signal Generation System Combining Amplifier Module and Distortion Compensation Technology
(a) Block diagram (b) Photo

Figure 3 Constellation of Generated 280 Gbps (35 GBaud 256-QAM) Modulated Signal9

Figure 4 Comparison with Previous Reports on Signal Generation in the J-Band

1. dBm

   A unit commonly used in radio and fiber-optic communications. Since these systems handle signals with a wide dynamic range of power, dBm expresses power levels relative to 1 milliwatt, using the formula: P(dBm) = 10 × log₁₀(P(mW)).

2. Modulation signal

   A signal in which information is embedded by converting it into a frequency suitable for transmission over a given communication channel—typically a higher frequency.

3. WR3.4 waveguide

   A waveguide is a physical structure used to guide electromagnetic waves, especially at high frequencies. WR3.4 is a standardized waveguide type used for the J-band (220 GHz–325 GHz).

4. InP (Indium Phosphorus) based compound semiconductor

   A type of III-V compound semiconductor composed of indium (In) and phosphorus (P). Compared to silicon (Si), it offers higher electron mobility and enables higher operating frequencies. It is widely used in fiber-optic communications and high-speed electronic devices.

5. Vector Component Analyzer:

   Keysight VNA (Vector Network Analyzer) based solution for component characterization, under modulated signal operating condition.
   https://www.keysight.com/us/en/assets/3123-1405/technical-overviews/6G-Vector-Component-Analysis.pdf

6. GBaud

   A unit representing the number of signal symbols transmitted per second, also known as symbol rate or modulation rate. 1 GBaud = 1,000,000,000 Baud.

7. 256-QAM

   Quadrature Amplitude Modulation (QAM) is a digital modulation method that conveys information by varying both amplitude and phase. 256-QAM modulates the signal into 256 distinct symbol points, enabling high data density.

8. Reference

   Keisuke Maekawa, Tomoya Nakashita, Toki Yoshioka, Takashi Hori, Antoine Rolland, Tadao Nagatsuma, “Single-channel 240-Gbit/s sub-THz wireless communications using ultralow phase noise receiver," Electronics Exp., vol. 21, no.3, pp. 20230584, 2024.

9. Constellations

   A visual representation of different signal states in digital communication. Each symbol is plotted as a point on a two-dimensional plane defined by in-phase and quadrature components, illustrating both amplitude and phase characteristics.

10. Amplifier module:

    https://www.ntt-innovative-devices.com/en/sensing_application/thz_products.html#j-band-power-amplifier